Skip to content

GPS shield

Description


The GPS Shield is base on the ublox's NEO-6M receiver module , and the footprints is compatible with Arduino/MEGA boards. The regular GPS pins (RX, TX) can be connected to D0-D7 of Arduino. Support software SerialPort and Micro SD card interface.

It's very easy using. You just need read SerialPort and then will get the GPS data. It also could use with GPRS Shield(click here to know how to use GPRS). So you can send GPS data to phone by SMS, then you can get the position of the GPS Shield.

The GPS Shield module interfaces to the customer’s application via one serial port, which uses CMOS voltage levels. support 3.3V / 5V IO operating. That's means 100% all Arduino main board compatible.

Model: MCS01107S
GPS Shield.jpg

Features


  • With standard Shield interface,it is compatible to all arduino main board.
  • With Micro SD interface
  • 3.3v and 5v logical voltage compatible
  • Active antenna design with high receive sensitivity, compatible normal antenna
  • Extremely fast time to first fix at low signal level
  • Operation temperature: -40c„ƒ ~ +85c

Specifications


NEO-6M-0-001

Interface function


Interface GPS Shield.png

Usage


Application 1: Print the GPS data with serial port

This example simply prints the output of the frames received by the GPS module to the serial port of an arduino.
first, connect the UART_RX to PD3, UART_TX to PD2.
second, upload the following demo code to Arduino or Crowduino.

//at 9600 bps 8-N-1
//Computer is connected to Arduino/Crowduino
//SoftSerial Shield is connected to the Software UART:D2&D3 

#include <SoftwareSerial.h>

SoftwareSerial SoftSerial(6, 7);
unsigned char buffer[256]; // buffer array for data recieve over serial port
int count=0;     // counter for buffer array 
void setup()
{
  SoftSerial.begin(9600);               // the SoftSerial baud rate   
  Serial.begin(9600);             // the Serial port of Arduino baud rate.

}

void loop()
{
  if (SoftSerial.available())              // if date is comming from softwareserial port ==> data is comming from SoftSerial shield
  {
    while(SoftSerial.available())          // reading data into char array 
    {
      buffer[count++]=SoftSerial.read();     // writing data into array
      if(count == 256)break;
  }
    Serial.write(buffer,count);            // if no data transmission ends, write buffer to hardware serial port
    clearBufferArray();              // call clearBufferArray function to clear the storaged data from the array
    count = 0;                       // set counter of while loop to zero


  }
  if (Serial.available())            // if data is available on hardwareserial port ==> data is comming from PC or notebook
    SoftSerial.write(Serial.read());       // write it to the SoftSerial shield
}
void clearBufferArray()              // function to clear buffer array
{
  for (int i=0; i<count;i++)
    { buffer[i]=NULL;}                  // clear all index of array with command NULL
}

Third, Open the serial monitor, select the serial rate as 9600. you will get the data return from the GPS modual.
Return data.jpg

Application 2: Use the u-center software to Locate your place

1. Down load the U-center software. you can also go to the U-blox office website to download this software. And install it.
2. Upload the demo code in Application 1 to Arduino.
3. Open U-center, choose the serial port and set the serial rate as 9600. After a while, you will get the location of the GPS shield.
U-center.jpg

See Also


FAQ


Please feel free to connect with techsupport@elecrow.com. We will list the normal question here and do our best to solve your problem.

Resouce